Manley SNAPPER® Monoblocks

DKK69,995.00

Lyder stærkt og naturligt ligesom rigtig musik.

Manley SNAPPER® Monoblocks EL34 x 4 = 100W

“They’ve got grip like nobody’s business…it’s really impressive. It has this ‘sound’…dang, these things are rock ‘n’ roll. That’s how I feel. That’s what I’m hearing.”

– Ron, New Record Day, April 2019 –

 

“The true test is if a particular component heightens the emotional involvement with the music. And at this, the Manley Snapper amplifiers truly excelled.”

– Jon T. Gale, The Stereo Times, April 2002 –

“…if you want your tunes served up in a gutsy, highly dynamic manner with a major serving of that inner righteousness that only tubes seem to provide, then the Snappers should be on your audition list.”

– Bill Cowen, SoundStage!, November 2002 –

“…the Snappers are a pair of powerful and exceptionally quiet monoblock tube amps…They are voiced to sound sweet and clear as rainwater, while retaining a serious dynamic punch. These amps make glorious music together.”

– The Inner Ear Report, June 2004 –

Specifikationer

  • Input Impedance RCA: 475 Kohm
  • Input Impedance XLR: 15 Kohm or 600 ohm switchable
  • Input Sensitivity RCA: 750mV input = 110W output
  • Input Sensitivity XLR @ 15Kohms: 1.5 V input = 110W output
  • Input Sensitivity XLR @ 600ohms: 2.4 V input = 110W output (w/600ohm source)
  • Gain RCA: factory set for 31 dB; Range = 29.5 to 34.5dB
  • Gain XLR: factory set for 25 dB
  • Negative Feedback: factory set for 9dB of global NFB
  • Maximum Output Power into 5 ohms: 110 Watts (1.5% THD @ 1kHz)
  • Maximum Output Power into 8 ohms: 100 Watts (1.5% THD @ 1kHz)
  • Signal to Noise Ratio Ref. 1W: Typically 90 dB A-WGT 20-20K
  • Noise Floor: Typically 105μV = -77dBu A-WGT
    Typically 388μV = -66dBu unweighted
  • Dynamic Range: 98dB
  • THD+noise @ 1W: less than 0.1%
  • Frequency Response at 110W full power: 15 Hz to 40 kHz FLAT
  • Frequency Response at 5W into 5 ohms: 10 Hz to 65 kHz FLAT, -3dB @ 100KHz
  • Recommended Speaker Load: Optimized for 5 ohms
  • Actual Output Impedance: 1.5 ohms
  • Power Consumption (idle): 170 Watts (1.4A @120VAC)
  • Power Consumption (at Full Power 110W): 336 Watts (2.8A @120VAC)
  • Operating Mains Voltage: Factory set for 100V, 120V or 220-240VAC operation for original destination country’s mains voltage.
  • Operating Mains Voltage: changeable with power transformer re-wiring and fuse value change.
  • Mains Voltage Frequency: 50~ 60Hz
  • Tube Complement (per pair of Snappers):
    • Input Vacuum Tube: 2 x Ruby 12AX7 (matched pair)
    • Driver Vacuum Tube: 2x 5687 or 7044 (equivalent) (matched pair)
    • Output Vacuum Tubes: 8 x Tungsol EL34B (matched)
  • B+ Voltage: 570V DC
  • Output Tube Quiescent Standing Current: 30mA
  • Set Bias for: 300mVDC measured across 10 ohm cathode resistor
  • Lamp type: “FuseLamp” size 1/4″ X 1 1/4″, 12 volt, 0.15 amp; Units built after 5/2003 use white LEDs
  • Fuse values & types for:
    • 120VAC operation: MDL or MDA 4 AMP / 250 Volt SLO-BLO size 1/4″ X 1 1/4″
    • 240VAC operation: MDL or MDA 2 AMP/ 250 Volt SLO-BLO size 1/4″ X 1 1/4″
  • B+ FUSE: MDA 1/2A Ceramic SLO-BLO size 1/4″ x 1 1/4″
  • Dimensions: 15″ deep x 13″ wide x 8.75″ tall
  • Shipping weight each: 45 pounds