Manley NEO-CLASSIC SE/PP 300B Monoblock Amplifiers

DKK89,995.00

Saftig mellemklasse, delikat detalje og forførende følelser.

Afgjort retro, 300B bringer dig til en svunnen tid, der fokuserede på enkelhed af design. Forvent saftig mellemklasse, delikat detalje og forførende følelser. Brugerkontrol af negativ feedback og evnen til at skifte topologi ‘on the fly’ fra 12 Watt i parallel SINGLE-ENDED-tilstand til 25 Watt i PUSH-PULL-tilstand er helt unik. Dette er en forstærker, der altid vil glæde og lokke dig, når den tilpasser sig en række effektive højttalere (og ører!).

“They were quiet, robust, and eminently user friendly…the Manley Neo-Classic SE/PP 300B definitely gets the nod as the go-to SE amp for the audiophile who wants it all.”

– Francis Vale, 21st, January 2005 –

“After months with the Manley Neo-Classic 300B amps I can happily say they have moved me in deep, wonderful and meaningful ways…I have never heard a component that makes a musical connection so effortlessly, readily and consistently.”

– Todd Warnke, EnjoyTheMusic.com, November 2001 –

“One thing is certain: the [Manley Neo-Classic SE/PP] aren’t run-of-the-mill; they are great sounding amplifiers and belong in a category where few designs can compete.”

– The Inner Ear Report, February 2002 –

 

“At the end of the day when all the audiophile obsessions over minutiae have been exhausted, you’re either left with a booby prize or the afterglow of an emotionally compelling musical encounter. Suffice to say that these 300B monos unequivocally stimulated the latter response…”

– 6moons.com, November 2003 –

Specifikationer

  • Vacuum Tubes: 2 x 300B (Output), 1 x 6SN7 (Driver), 1 x 6SL7 (Input),
    2 x 5AR4 (Rectifier). (Units prior to 2011 used 5U4 rectifier tubes.)
  • Output Power @ 1kHz with 5 dB FeedBack in SINGLE-ENDED: 11 Watts @ 3% THD
  • Output Power @ 1kHz with 5 dB FeedBack in PUSH-PULL: 24 Watts @ 1.5% THD
  • Frequency Response with 5 dB FB in SINGLE-ENDED: 15 Hz – 15 kHz ±0.5 dB (measured at 5 watts)
  • Frequency Response with 5 dB FB in PUSH-PULL: 10 Hz – 20 kHz ±0.5 dB
  • GAIN SE Mode 0dB Feedback Setting: 30 dB
  • GAIN SE Mode 10dB Feedback Setting: 20 dB
  • Input Sensitivity with 5db FB SINGLE ENDED: 700mV for Maximum Power
  • Input Sensitivity with 5db FB PUSH-PULL: 450mV for Maximum Power
  • Input Sensitivity with 5db FB SINGLE ENDED: 165mV for 1V output into 8 Ohms
  • Input Sensitivity with 5db FB PUSH-PULL: 160mV for 1V output into 8 Ohms
  • S/N Ratio: SINGLE ENDED: 83.5dB Ref. 1W; 2.83v//8 Ohms,20KHz BW; 5dB FB.
  • S/N Ratio: PUSH-PULL: 85.4dB Ref. 1W; 2.83v//8 Ohms; 20KHz BW; 5dB FB.
  • Dynamic Range: SINGLE ENDED: 94dB Ref. 3% THD; 20KHz BW; 5dB FB.
  • Dynamic Range: PUSH-PULL: 99.5dB Ref. 1.5% THD; 20KHz BW; 5dB FB.
  • Input Impedance: 100 kOhm, direct coupled.
  • Optimum Speaker Load (switchable): 4 to 12 Ohm range appropriate for 4 & 8 Ohm speakers
  • – 12 to 20 Ohm range appropriate for 16 Ohm speakers
  • Actual Output Impedance SINGLE ENDED: 2.25 Ohms
  • Actual Output Impedance PUSH-PULL: 1.86 Ohms
  • Damping Factor SINGLE ENDED: 3.5
  • Damping Factor PUSH-PULL: 4.3
  • Maximum Power Consumption: 240 Watts
  • Mains Voltage Frequency: 50~ 60Hz
    • Power transformer factory set for 100V, 120V or 220-240VAC operation for original destination country’s mains voltage.
    • Operating Mains Voltage changeable with power transformer re-wiring and fuse value change.
  • Mains Fuse 100-120VAC operation: MDA 3 Amp SLO-BLO Ceramic Time-Delay fuse
  • Mains Fuse 220-240VAC operation: MDA 1.5 Amp SLO-BLO Ceramic Time-Delay fuse
  • B+ Fuse: MDA 400 mA SLO-BLO Ceramic Time-Delay fuse
  • Badge Illumination: Units produced before 7/2003 use 8V, 0.3A “Fuse-Lamp” 1/4″ X 1 1/4″ – Serial numbers after NSEPP314 use LED illumination which probably won’t burn out
  • Dimensions: W= 8.5, D= 23, H= 9 inches, Including projecting controls and parts
  • Minimum Mounting Surface Dimensions: Feet Footprint = W= 7.5″ D= 18″
  • Shipping Weight: 41 lbs. each