Manley STEELHEAD® RC Phono Stage

DKK79,995.00

STEELHEAD er ren, stille og skudsikker med enorm fleksibilitet og er både en tweak-o-holic tube-elskers drøm og en hifi-anmelders reference.

Beskrivelse

STEELHEAD er ren, stille og skudsikker med enorm fleksibilitet og er både en tweak-o-holic tube-elskers drøm og en hifi-anmelders reference.

“Overall, the Steelhead delivered the best vinyl playback I’ve heard from my system. It combined speed, frequency extension, resolution, harmonic structure, focus, air, stage depth, image specificity, and, most important, overall musical coherence in a way that made the music seem to fly from the speakers unrestrained by mechanical or electrical bounds.”

– Michael Fremer, Stereophile, December 2001 –

“…the Steelhead is a very fine phonostage. And no, you’re not just paying for flexibility — the damn thing sounds great and very easily competes with a purist-design…and well, the Steelhead is so pretty. I guess you could say I’m a fan of the aesthetic. Very MANLEY.”

– Scot Hull, Part-Time Audiophile, January 2011 –

“The Manley Steelhead is a tube phono pre-amp with all the qualities we love about tubes and none of the limitations of those thermionic devices…I lay odds that whatever kind of audiophile you consider yourself to be, you’ll find yourself more involved in the music.”

– Marshall Nack, Stereo Times, December 2002 –

“I’ve had my Steelhead RC for 7 years now. Being an audiophile, a lot of changes have been made to my system through the years, but I’m positive that the Steelhead will never leave.”

– Le N. (Customer) –

Specifikationer

Vacuum tube complement: 6922 SOVTEK Russian x 2 (gain) plus JAN NOS GE 7044 or 5687 x 4 (output buffers)
Fuse type and ratings @ 117 VAC operation: 1.5 Amp 3AG slow-blow mains fuse 0.5 Amp 3AG slow-blow logic fuse
Fuse type and ratings @ 230 VAC operation: 0.75 Amp 3AG slow-blow mains fuse 0.25 Amp 3AG slow-blow logic fuse
Moving Magnet input impedance: 5-step user adjustable via fixed low-noise resistors. 25, 50, 100, 200 and 47000 Ohms.
Moving Coil input impedance: 5-step user adjustable via multi-tap autoformer: 25, 50, 100, 200 and 400 Ohms.
Input Termination Capacitance: Front Panel Selectable in 10 picofarad steps from 10 to 1100 pF (1.1nF) Residual input capacitance less than 40 pF.
Gain: 4-step user adjustable, 50, 55, 60 and 65 dB active gain at 1 kHz referred to the FIXED output jack into a 10 kOhm load. Additional gain available via the MC input’s step-up autoformer. See Owner’s Manual for discussion.
Deviation from RIAA curve: Less than +0.5 / -0.3 dB from 20 Hz to 20 kHz at any gain setting. Typically less than ±1 dB from 10 Hz to 100 kHz
Inter-channel differential phase: Less than 4 degrees from 20 Hz to 20 kHz at any gain setting. Typically less than 2 degrees.
Inter-channel differential gain: Less than ±0.5 dB from 20 Hz to 20 kHz at any gain setting.
Dynamic Range: 101 dB @ 1 kHz, 1% THD measured with 200 Ohm source, 47 kOhm input, @ 55dB Gain 97 dB @ 1 kHz, 0.1% THD
THD: 0.0042% at 1V output @1kHz
REMORA RF REMOTE: controls motorised volume control up/down functions; uses 9v battery
Maximum MM input level: 50 mVrms @ 1KHz for an output of 17 Vrms or -23.8 dBu @ 1KHz for an output of +27 dBu @ 1.5% THD
Maximum MM input level: 93 mVrms @ 1KHz for an output of 29 Vrms or -18.4 dBu @ 1KHz for an output of +32.3 dBu @ 10% THD
Maximum MC input level: 39 mVrms @ 1KHz for an output of 17 Vrms or -26 dBu @ 1KHz for an output of +27 dBu @ 1.5% THD
Maximum MC input level: 72 mVrms @ 1KHz for an output of 29 Vrms or -20.6 dBu @ 1KHz for an output of +32.3 dBu @ 10% THD
Maximum LINE input level: 26.5Vrms @ 1KHz for an output of 22.8Vrms or +30.6dBu @ 1KHz for an output of +29.3dBu @ 0.07% THD
Maximum Output: +27dBm @ 1KHz with 3% THD into 100 kOhm load
FIXed Output impedance: 150 Ohms. Minimum suggested load greater than 1500 Ohms.
VARIable Output impedance: 75 Ohms. Minimum suggested load greater than 600 Ohms.

Variable Output


GAIN Setting
Fixed Output
9:00
12:00
V/C FULL

MM Noise (S+N+D) / (N+D):
50 dB
86dB
108dB
99dB
86dB

200 Ohm source, 47 kOhm input

A-weighted Referred to 2.54 mV

rms @ 1 kHz
55 dB
84dB
108dB
99dB
85dB

60 dB
80dB
108dB
94dB
80dB

65 dB
75dB
108dB
89dB
75dB



MC Noise (S+N+D) / (N+D):
50 dB
84dB
108dB
98dB
85dB

100 Ohm source, 100 Ohm input

A-weighted Referred to 0.5 mV

rms @ 1 kHz and rated Input Z
55 dB
80dB
108dB
95dB
81dB

60 dB
75dB
108dB
90dB
76dB

65 dB
70dB
107dB
85dB
71dB

Power consumption: 100 watts
Outboard Power Supply: is factory set for 100V, 120V or 220-240VAC operation for original destination country’s mains voltage.
Operating Mains Voltage: 120 to 240VAC operation changeable with power transformer re-wiring via internal switch and fuse value change. 100VAC operation changeover achieved via rewiring of power transformer PCB.
Mains Voltage Frequency: 50~ 60Hz
PSU Regulation good for 65% rated voltage: 75VAC for 117V unit or 150VAC for 234V wired unit.
Unit weight: Steelhead: 15 lbs. – PSU: 18 lbs.
Chassis dimensions: Steelhead: 19 wide x 3.5 tall x 15.5 deep – PSU: 13.5 wide x 4.5 tall x 11.375 deep
PSU umbilical cord length: 5 1/2 feet approx. 1.65m

Minimum mounting allocation footprint including all projecting parts and controls:

Steelhead: 19 wide x 4.125 tall x 18 deep – (allow an additional 6 inches depth for PSU umbilical cord projecting out in the center)
PSU: 13.5 wide x 4.625 tall x 12.5 deep – (allow an additional 6 inches depth for PSU umbilical cord projecting out in the left)
Your phono input cables need to be able to spread 9″ apart.
Your LINE input RCA cables need to be able to spread 12.250″ apart.
Your Output cables need to be able to spread 15″ apart.
The chassis itself is 17″ wide. The faceplate is 19″ wide.